I've seen many places on this forum discussions about cooling the Xboxes. Many still want the iceberqs, but they are getting hard to come by, then i stumbled over a thread on the facebookpage "Xbox (Original) Modding, Trading, Collecting, Discussion (OGXbox.com)", with som heatsinks with fans. They dont seem to outperfom the original heatsinks in a standard case, but i guess they could work well in a slim,
I am borrowing the picture and info provided in this thread from the person that made the mod, and he asked to be credited: Peter Nikoloudis
His temps after playing for several hours
'
Apparently they are silent too
There are some discussions on mounting. The original modder used the holes for holding down the motherboard, he had to drill them out a bit and also drill the heat sink holes. Some in the discussion thinks it would be better to use the holes for the original plastic retainers.
Link to the heatsinks: https://www.aliexpress.com/item/1-Piece ... autifyAB=0
Heatsinks with fan for the Xbox
- LudviG
- Posts: 267
- Joined: Sun Jul 15, 2012 10:05 pm
- Location: Norway
- Has thanked: 29 times
- Been thanked: 13 times
Heatsinks with fan for the Xbox
Last edited by LudviG on Sun Mar 18, 2018 11:32 pm, edited 1 time in total.
Never argue with an idiot! First he brings you down to his level, then he beats you with experience.
Heatsinks with fan for the Xbox
Hey guys,
Just make sure you sand down the anodised coating in the bottom of the heat sinks, it helps the temperatures a lot and gets them flat as they come a little buckled.
The reason I used the bolt method was to make sure there is enough pressure and the plastic clips on the heatsinks are completely useless for the Application.
You don’t need to drill out the motherboard holes, all existing holes are used and there is plenty of unexposed internals so you won’t damage anything is done correctly! but I had to use a 3/16 bit just because of the bolts I used, but drilling the heatsinks is a must and use good thermal compound.
This mod won’t work on a 1.6!
I’m not responsible if your wreck your console!
Sent from my iPhone using Tapatalk
Just make sure you sand down the anodised coating in the bottom of the heat sinks, it helps the temperatures a lot and gets them flat as they come a little buckled.
The reason I used the bolt method was to make sure there is enough pressure and the plastic clips on the heatsinks are completely useless for the Application.
You don’t need to drill out the motherboard holes, all existing holes are used and there is plenty of unexposed internals so you won’t damage anything is done correctly! but I had to use a 3/16 bit just because of the bolts I used, but drilling the heatsinks is a must and use good thermal compound.
This mod won’t work on a 1.6!
I’m not responsible if your wreck your console!
Sent from my iPhone using Tapatalk
-
- Posts: 13
- Joined: Fri Jul 06, 2012 8:19 am
Re: Heatsinks with fan for the Xbox
have you been able to locate any of these heatsink/fans on amazon? I dont know what I am looking for.
I really dont want to put my cc number on another site.
I really dont want to put my cc number on another site.
Re: Heatsinks with fan for the Xbox
Here is a link for them on eBayJustinBeaird wrote:have you been able to locate any of these heatsink/fans on amazon? I dont know what I am looking for.
I really dont want to put my cc number on another site.
https://rover.ebay.com/rover/0/0/0?mpre ... 3550798441
Sent from my iPhone using Tapatalk
-
- Posts: 2
- Joined: Sun Feb 04, 2018 1:56 am
Re: Heatsinks with fan for the Xbox
Did you completely sanded down the anodised part or just sand a bit ? Also it will run with just this two fan heatsinks or it need another fan like the original one?peter_nik wrote:Hey guys,
Just make sure you sand down the anodised coating in the bottom of the heat sinks, it helps the temperatures a lot and gets them flat as they come a little buckled.
The reason I used the bolt method was to make sure there is enough pressure and the plastic clips on the heatsinks are completely useless for the Application.
You don’t need to drill out the motherboard holes, all existing holes are used and there is plenty of unexposed internals so you won’t damage anything is done correctly! but I had to use a 3/16 bit just because of the bolts I used, but drilling the heatsinks is a must and use good thermal compound.
This mod won’t work on a 1.6!
I’m not responsible if your wreck your console!
Sent from my iPhone using Tapatalk
Enviado desde mi SAMSUNG-SM-N920A mediante Tapatalk
Re: Heatsinks with fan for the Xbox
It uses the original exhaust fan on the back to, I just upgraded mine to a 80mm
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
Re: Heatsinks with fan for the Xbox
And I Sanded all the coating off
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk